Crown XTI6002 Power Amplifier 1200W @ 8 Ohms

Crown XTi 6002 1200-Watt Amplifier @ 8 Ohms

2 Ohms Stereo (per ch.) 3000W
4 Ohms Stereo (per ch.) 2100W
8 Ohms Stereo (per ch.) 1200W
8 Ohms Bridge-Mono 4200W
4 Ohms Bridge-Mono 6000W

There's no debate – when you choose Crown's XTi 2 Series, you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series Crown power amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.

Next Generation Features:

Peakx Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
New system monitoring provides software visibility of AC line voltage and power supply temperature
Integrated cast-aluminum handles for easy handling and enhanced durability
Locking power cord clip provides a secure connection between the amplifier and power cord
Updated HiQnet Band Manager and System Architect control software
Increased number of presets to a total of 30; 29 of which are user definable

PERFORMANCE

Input EQ:

6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.

Crossover Filters:

Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.

Output EQ:

8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.

Delay:

For signal alignment of driver; 50 mS of total delay.

SubHarmonic Synth:

Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.

Peakx Plus Limiter:

User defeatable limiter that allows users to control Threshold, Attack, and Release times.

Presets:

30 total presets, 29 of which are user-definable.

Sensitivity (for full rated power at 4 ohms):

1.4 Vrms

Frequency Response (at 1 watt, 20 Hz - 20 kHz):

+0 dB, –1 dB

Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms):

100 dB (A weighted)

Total Harmonic Distortion (THD):

Damping Factor 20 Hz to 1 kHz
Crosstalk (below rated power)
20 kHz - 1 kHz: > 70 db
Input Impedance (nominal)
20k ohms balanced, 10k ohms unbalanced

Maximum Input Signal:

+22 dBu typical
AC Line Voltage and Frequency Configurations
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz

AC Line Current:

8.3A; no more than 38W at idle

Operating Temperature:

0°C to 40°C at 95% relative humidity (non-condensing)

Level:

Two front-panel rotary level controls, one for each channel
Power Switch
On/Off switch applies AC power to the amplifier
Sel/Prev/Next Buttons
Three buttons near the LCD screen that are used to access menu items and front panel lockout
LCD Screen
Backlit liquid crystal display that shows preset and processing status

Indicators

Signal Indicator:

Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).

–10 Indicator:

Green LED flashes when output signal exceeds -10 dB below clip.

–20 Indicator:

Green LED flashes when output signal level exceeds -20 dB below clip.

Ready Indicator:

Green LED, one per channel, illuminates when the amplifier is ready to produce audio.

Clip Indicator:

Red LED, one per channel, turns on at the threshold of audible distortion

Temp Indicator:

Red LED, one per channel, illuminates under excessive temperature conditions

Power Indicator:

Blue LED illuminates when the amplifier has been turned on and has power

Input/Output Connectors

Input Connectors:

XLR, one per channel
Link/Out Connector
Loop-thru signal from input connector for linking another amplifier, one per channel.

Output Connectors:

Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).
HiQnet USB Connector
Type B, connects to HiQnet network.

Construction

Chassis: