Martin P3 PowerPort 1000 IP Install Power Supply

Martin P3 PowerPort 1000 IP Install Power Supply

The P3 PowerPort 1000 IP Install is an integrated power supply and data processor for Martin’s range of creative LED video products, including the Exterior PixLine™ and VC-Dots™. When driven by one of Martin’s award-winning P3™ System Controllers™, it combines stable power delivery with high-speed, high-capacity video processing. Setup and configuration are easy and intuitive. A full outdoor rating and optional fiber interface make the product perfect for permanent outdoor installations.

• Power and data processor for all Martin’s fixed-installation creative LED video products
• Flexible integration: can be located remotely, indoors or outdoors
• Easy cabling and configuration

Features:

• P3 image processing technology
• Set-up and addressing via P3 System Controller family
• No local configuration needed
• P3 input and thru to allow daisy-chaining
• Optional fiber-interface
• 4 hybrid power/data output ports
• Wall-mountable or free-standing
• Can be located up to 50 m away from the creative LED video products
• IP66

Specifications:

• Physical
• Length: 426 mm (16.8 in.)
• Width: 483 mm (19.1 in.)
• Height: 146 mm (5.8 in.)
• Weight: 8 kg (17.7 lbs.)
• Control and Programming
• Addressing and status: Via P3 System Controller
• Mapping: Via P3 System Controller
• Firmware update: Via P3 System Controller
• Control/User Interface
• Device status: Multicolor status LED
• Power output status: Four LEDs
• Data output status: Four LEDs
• Device test and reset: Pushbutton to call up local test patterns and reset device
• Status LEDs and pushbutton can be disabled remotely if required
• P3 Signal Protocol
• Signal type: Gigabit Ethernet
• Protocol: Proprietary Martin P3
• Hot pluggable: Yes, electrically isolated at all connections
• Cable type: Ethernet, CAT 5e or better
• Cable length: Up to 100 m (328 ft.) between any 2 devices, extendable with Ethernet switch or conversion to fiber
• System integration
• VC-Dot™ family via VC-Feeder™
• Exterior PixLine™ family
• VDO Sceptron™ family
• VC-Grid™ family (indoor product)
• VC-Strip™ family (indoor product)
• Exterior Dot-HP™ family
• Construction
• Protection rating: IP66
• NEMA enclosure rating: Type 3
• Housing: Aluminum
• Color: Alu grey (customized colors available on project basis)v
• Effective Projected Area (EPA): 0.21 m2RoHS compliant
• Installation
• Mounting: Brackets for installation on flat surface
• Orientation: Any, except with cable glands facing up or lid facing down
• Connections
• Power input: Cable gland (M20), internal screw terminals
• P3 data in/out: Two cable glands (M16), two internal RJ45 connectors (if copper-to-fiber unit is installed, one cable gland can be used for fiber)
• Combined power & data out: Four cable glands (M16), internal screw terminals
• M16 cable glands accept 5.5 - 10 mm cable, M20 glands accept 8-13 mm cable
• Electrical
• AC power: 120-277 V nominal, 50/60 Hz
• Power supply units: Auto-ranging electronic switch-mode
• Typical total power consumption: 1000 W (including full load of connected display devices, all at full intensity)
• Typical half-cycle RMS inrush current at 230 V, 50 Hz: 20.9 A
• Total power consumption in idle state (at 25° C, all connected devices powered off): 22 W
• Thermal
• Cooling: Convection
• Maximum ambient temperature (Ta max.): 55° C
• Minimum ambient temperature (Ta min.): -30° C
• Total heat dissipation (calculated, +/- 10%): 345 BTU/hr. (not including display devices but with system at full load)
• Approvals
• EU safety: EN 60950
• EU EMC: EN 55032, EN 55103-2, EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
• US safety: ANSI/UL 60950-1
• Canadian safety: CSA C22.2 No. 60950-1