Brainstorm Electronics SR-112 Time Code Generator
The SR-112 reshapes and distributes timecode through its 12 outputs, sending it over long lines with no signal degradation. It analyzes the source for quick diagnostic and generates or repairs timecode, locked to video if required.
Features:
- 1 x 12 DISTRIBUTOR / RESHAPER
- Designed to send clean time code over long cables
- Eliminates level fluctuations
- Buffered outputs; balanced or unbalanced
- TIME CODE ANALYZER
- Identifies time code format, reports errors (drop outs…)
- Monitors video phase
- Generates a comprehensive report via Ethernet
- TIME CODE GENERATOR (option)
- Generates new time code with or without video reference
- Repairs faulty time code (jam sync)
Specifications:
- TC Distributor: 1×12
- TC Input Connector: XLR Female
- TC Output Connectors: 1 x DB-25 F (8 outputs – Tascam/Avid analog pin configuration), 2 x XLR M, 2 x 1/4” TRS
- Input Signal: SMPTE/EBU Longitudinal Time Code
- Impedance: 20KΩ bal.; 10KΩ unbal.
- Level: -30dbU min; +20dbU Max
- Output Signal: Waveform: switchable rise time: 1us (square); 25us (SMPTE); 50us (EBU)
- Impedance: 600Ω bal.; 300Ω unbal.
- Level: adjustable: full off to +8dbU bal.; to + 2dbU unbal.
- Amplitude distortion: less than 2%
- Status LEDs: Reshape • Generate (TCG option) • Video In • Repair (TCG option) • TC In • Ethernet
- Warning LEDs: Input Error (red) • Video Drift (red) • Video Phase (yellow) • Video Termination Off (yellow)
- Time Code Reader: The 8 digit LED Display indicates hours, minutes, seconds and frames.
- The display also flashes error descriptions when detected.
- LCD Display:
- In addition to being used for SET UP, the 32 character LCD display indicates the following:
- Format and rate of the incoming time code
- Format and rate of the video reference
- User Bits
- Video Phase
- List of errors
- Connectors:
- Time Code in: XLR Female (x 1)
- Video Ref: BNC (x 1)
- Time Code outputs:
- DB25 (1x) – Tascam/Avid analog pin configuration: outputs 1-8
- XLR Male (2x): outputs 9-10
- 1/4” jacks (2x) – TRS: outputs 11-12
- Ethernet: RJ45 jack (x 1)
- Power: 4 pin circular (x 2)
- Power: 12VDC @ 3A
- Redundancy: two separate supplies can be connected to the 2 separate power inputs. If one supply fails, the other takes over and an error is reported.
- The faulty supply can be swapped without having to power down.
- Dimensions: 19” x 8.125” x 1.75” (48.26 cm x 20.64 cm x 4.45cm)
- Designed to send clean time code over long cables
- Eliminates level fluctuations
- Buffered outputs; balanced or unbalanced
- Identifies time code format, reports errors (drop outs…)
- Monitors video phase
- Generates a comprehensive report via Ethernet
- Generates new time code with or without video reference
- Repairs faulty time code (jam sync)
- TC Distributor: 1×12
- TC Input Connector: XLR Female
- TC Output Connectors: 1 x DB-25 F (8 outputs – Tascam/Avid analog pin configuration), 2 x XLR M, 2 x 1/4” TRS
- Input Signal: SMPTE/EBU Longitudinal Time Code
- Impedance: 20KΩ bal.; 10KΩ unbal.
- Level: -30dbU min; +20dbU Max
- Output Signal: Waveform: switchable rise time: 1us (square); 25us (SMPTE); 50us (EBU)
- Impedance: 600Ω bal.; 300Ω unbal.
- Level: adjustable: full off to +8dbU bal.; to + 2dbU unbal.
- Amplitude distortion: less than 2%
- Status LEDs: Reshape • Generate (TCG option) • Video In • Repair (TCG option) • TC In • Ethernet
- Warning LEDs: Input Error (red) • Video Drift (red) • Video Phase (yellow) • Video Termination Off (yellow)
- Time Code Reader: The 8 digit LED Display indicates hours, minutes, seconds and frames.
- The display also flashes error descriptions when detected.
- LCD Display:
- In addition to being used for SET UP, the 32 character LCD display indicates the following:
- Format and rate of the incoming time code
- Format and rate of the video reference
- User Bits
- Video Phase
- List of errors
- In addition to being used for SET UP, the 32 character LCD display indicates the following:
- Connectors:
- Time Code in: XLR Female (x 1)
- Video Ref: BNC (x 1)
- Time Code outputs:
- DB25 (1x) – Tascam/Avid analog pin configuration: outputs 1-8
- XLR Male (2x): outputs 9-10
- 1/4” jacks (2x) – TRS: outputs 11-12
- Ethernet: RJ45 jack (x 1)
- Power: 4 pin circular (x 2)
- Power: 12VDC @ 3A
- Redundancy: two separate supplies can be connected to the 2 separate power inputs. If one supply fails, the other takes over and an error is reported.
- The faulty supply can be swapped without having to power down.
- Dimensions: 19” x 8.125” x 1.75” (48.26 cm x 20.64 cm x 4.45cm)