D&B Audiotechnik Y-Series Portable Powered PA System with Y7P Speakers / B6 Sub and Touring Cases

This live sound reinforcement speaker package contains the following items:

*(2x) D&B Audiotechnik Z0702-001 Y7P Loudspeaker NL4

The compact, 2-way passive Y7P loudspeaker features two 8” drivers in a dipole arrangement with a 1.4” compression driver mounted onto a rotatable CD horn. Sophisticated horn geometry combined with the advanced bass-reflex port design delivers full bandwidth capabilities with an extended LF output. These point source, high performance cabinets offer 75° horizontal directivity controlled down to 500 Hz, matched with a vertical dispersion of 40°. The horn can be rotated by 90° to enable horizontal orientation. The Y7P provides a broad variety of deployment possibilities, especially when used as a stand-alone full range system, or combined with other elements from the Y-Series, either ground stacked or flown. The loudspeaker cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam. The cabinet incorporates a pair of handles whilst M10 threaded inserts are provided for attaching d&b rigging hardware. Additionally, two further M10 sockets accept the 8mm load pin to expand the mounting options.

Amplifiers

The following amplifiers can be used to drive the Y7P.

• Mobile
• D20
• D40
• D80
• Installation
• 40D

Technical Data

• System data
• Frequency response (-5 dB standard)
• 59 Hz - 18 kHz
• Frequency response (-5 dB CUT mode)
• 118 Hz - 18 kHz
• Max. sound pressure[1]
• with 10D
• 132 dB
• with D20/30D
• 135 dB
• with D40/D80/40D
• 137 dB
• Cabinets per amplifier channel
• 2
• Loudspeaker data
• Configuration
• High performance 2-way passive point source loudspeaker
• Nominal impedance
• 8 Ω
• Power handling capacity (RMS/peak 10 ms)
• 400/1600 W
• Nominal dispersion angle (h x v)
• 75° x 40°
• Components
• 2 x 8" driver with neodymium magnet
• 1.4" exit compression driver
• passive crossover network
• Connections
• 2 x NL4
• Dimensions / weight
• Dimensions (H x W x D)
• 580 x 257 x 341 mm
• 22.8 x 10 x 13.4"
• Weight
• 18 kg
• 40 lb

[1] 1 m, free field, SPL max peak test signal: pink noise with crest factor 4, one speaker driven

*(2x) D&B Audiotechnik B6 High Performance Subwoofer NL4

The B6-SUB is a high performance subwoofer designed for ground stacked applications, housing a long excursion 18” driver built into a bass-reflex design. When three or any multiple of three B6-SUBs are used, they can be positioned in a Cardioid Subwoofer Array with one cabinet physically facing backwards and driven by an amplifier channel with CSA mode selected. This achieves exceptional directivity control in lower frequencies and significantly reduces the energy radiating towards to the rear. The cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam, whilst the side panels incorporate two handles. Four wheels are mounted to the rear and the enclosure features two runners to protect the bottom panel from scratching. Two correspondingly shaped recesses are incorporated into the top panel of each cabinet to accept these runners, preventing cabinet movement when stacked. An M20 threaded flange in the top panel accepts the d&b Loudspeaker stand winder M20. An optional transport lid protects the front of the subwoofer during transit.

Amplifiers

The following amplifiers can be used to drive the B6-SUB.

• Mobile
• D20
• D40
• D80
• Installation
• 40D

Technical Data

• System data
• Frequency response (-5 dB standard)
• 37 Hz - 140 Hz
• Frequency response (-5 dB 100 Hz mode)
• 37 Hz - 110 Hz
• Frequency response (–5 dB INFRA mode)
• 35 Hz - 80 Hz
• Max. sound pressure[1]
• with 10D
• 128 dB
• with D20/30D
• 131 dB
• with D40/D80/40D
• 134 dB
• Cabinets per amplifier channel
• 2
• Loudspeaker data
• Configuration
• High performance subwoofer
• Nominal impedance
• 8 Ω
• Power handling capacity (RMS/peak 10 ms)
• 500/2000 W
• Components
• 1 x 18" driver
• Connections
• 2 x NL4
• Dimensions / weight
• Dimensions (H x W x D)
• 490 x 580 x 700[2] / 805 mm
• 19.3 x 22.8 x 27.5[2] / 31.7"
• Weight
• 41 kg
• 90 lb

[1] 1 m, free field, SPL max peak test signal: pink noise with crest factor 4, one speaker driven

[2] dimensions without wheels

*(1x) D&B Audiotechnik D20 Four Channel Amplifier

The 2 RU four channel D20 amplifier is ideally suited to mobile and installation applications which require low to medium Sound Pressure Level (SPL) capabilities. The D20 features the same Digital Signal Processing (DSP) platform as the latest generation of d&b amplifiers, containing configurations for all d&b loudspeakers except the J-Series and the M2 monitor, plus a linear mode. The signal delay capability enables user definable settings of up to 10 s (= 3440 m/11286 ft), which can be applied independently to each channel. The same applies to the two 16-band equalizers, providing optional parametric, asymmetric, shelving or notch filtering. The D20 incorporates a colour TFT touchscreen, offering quick access to the menu structure, while the rotary encoder can be used for fine adjustment. The front panel and the integrated touchscreen are tilted up for easy operation when the amplifier is below eye level. The equal ratio of signal input to amplifier output channels increases application flexibility particularly for monitor, frontfill or effect channel use. The LoadMatch function integrated within the D20 amplifier electrically compensates for the properties of loudspeaker cable used. The D20 incorporates Class D amplifiers utilizing a power supply with active Power Factor Correction (PFC) suitable for mains voltages 100 V - 240 V, 50 - 60 Hz and maintains a stable output when used with weak or unstable mains supplies. An NL8 provides all outputs on a single connector for loudspeaker multicores. Dual channel mode is driven through four individual NL4 connectors, while Mix TOP/SUB and 2-Way Active mode output configurations for applicable d&b loudspeakers are available via two central NL4 connectors. etherCON and RJ 45 connectors enable access to the d&b Remote network through OCA/AES70 via Ethernet and through CAN-Bus respectively.

The D20 Touring rack assembly

The D20 Touring rack assembly is designed as a fully equipped and prewired system rack, providing mains power distribution, connector interfaces and all internal cabling for three D20 amplifiers[1]. It is equipped with a 32 A CEE mains power connector, a mains distribution device with a 32 A mains link, and a loudspeaker connector panel.

All internal audio and remote connections are fully prewired. A loom comprising two AES3 cables and one CAT5/etherCON[2] is supplied, providing patch cabling for a network connection and four AES3 channels. The D20 Touring rack assembly is provided with either a DS10 Audio network bridge, which comes supplied with all necessary cabling, or a 1 RU drawer.

The DS10 Audio network bridge interfaces between Dante networks and AES3 digital audio signals, while also providing distribution of Ethernet control data. The DS10 can deliver up to sixteen Dante network channels via AES3 digital signal outputs, and is intended to integrate directly into a D20 Touring rack assembly. The front panel of the DS10 is designed to align with the input panel of the D20 Touring rack assembly. The DS10 can be powered by one of the auxiliary mains outputs. All necessary patch cabling and links are supplied with a D20 Touring rack assembly including a DS10.

The 10 RU Touring rack houses a 19" internal shockmount steel frame accommodating three D20 amplifiers and the requisite connection panels. It comes with two sliding doors, a perspex window at the front, four wheels, six handles and recessed stacking moulds at the top.

The DS10 Rack upgrade kit contains everything required to replace the drawer within the D20 Touring rack assembly with a DS10. This kit includes a DS10 Audio network bridge, a powerCON[2] to powerCON[2] mains cable, an Ethernet patch cable and two AES3 XLR patch cables.

Technical Data

• Digital Signal Processing
• Equalizer
• 2 x 16-band PEQ/notch/shelving/asymmetric
• Latency analog and digital inputs
• 0.3 ms
• Delay setting
• 0.3 - 10000 ms
• Configurations
• current d&b loudspeakers (except SL-Series, J-Series, M2) and linear mode
• Function switches
• d&b loudspeaker specific circuits
• Frequency generator
• Pink noise or Sine wave
• Sampling rate
• 96 kHz/27 Bit ADC/24 Bit DAC
• Controls and indicators
• POWER
• Mains power switch
• SCROLL/EDIT
• Digital rotary encoder
• Display
• Colour TFT touchscreen, 3.5"/320 x 240 pixel
• ISP, GR, OVL A/B
• Colour TFT
• Connectors
• INPUT ANALOG (A1 - A4)
• 3 pin XLR female
• ANALOG LINK (A1 - A4)
• 3 pin XLR male
• INPUT DIGITAL (D1/2, D3/4)
• 3 pin XLR female AES3
• DIGITAL LINK (Output)
• 3 pin XLR male
• Sampling Digital AES/EBU
• 48 kHz/96 kHz
• Speaker outputs A/B/C/D
• NL4
• Mix TOP/SUB / 2-Way Active output A/B and C/D
• NL4
• 4 Channel output
• NL8
• CAN
• 2 x RJ 45 parallel
• ETHERNET
• 2 x etherCON®, 10/100 Mbit Ethernet
• Mains connector
• powerCON®
• Data (linear setting with subsonic filter)
• Maximum output power per channel (THD+N < 0.5%, all channels driven)
• CF = 6 dB at 4 / 8 ohms
• 4 x 1000/800 W
• CF = 12 dB at 4 / 8 ohms
• 4 x 1600/800 W
• S/N ratio (unweighted, RMS)
• Analog input
• > 104 dBr
• Digital input
• > 106 dBr
• Power supply
• Type
• Universal range switch mode power supply with active PFC
• Rated mains voltage
• 100 - 240 V, 50 - 60 Hz
• Dimensions / weight
• Dimensions (H x W x D)
• 2 RU x 19" x 460 mm/18.1"
• Weight
• 10.8 kg/23.8 lb

[1] The Touring rack assembly does not come with D20 amplifiers.

[2] etherCON® and powerCON® are registered trademarks of Neutrik AG, Liechtenstein.

*(1x) D&B Audiotechnik Z5397-001 YP Swivel Bracket

Using the Z5024 Loudspeaker stand adapter, YP cabinets can be mounted onto a loudspeaker stand with a tube diameter of 35 mm (1.4").

Using the Z5010 TV spigot with fixing plate in conjunction with the Z5012 Pipe clamp, YP cabinets can be vertically flown from overhead bars or trusses with a tube diameter between 40 mm and 70 mm (1.5" and 2.75").

The horizontal aiming as well as the vertical aiming can be set continuously.

*(1x) D&B Audiotechnik Z5024-000-00 Loudspeaker Stand Adapter

This adapter is used to mount loudspeakers on to the standard 35 mm diameter column commonly used for loudspeaker stands.

• − Direct assembly to E1 or E3 loudspeakers
• − Direct assembly to 2 x E3 using Z5031 E3 Standard bracket
• − Z5023 02 Flying bracket
• − Z0124 E1 Vertical bracket
• − Z0126 E1 Horizontal bracket
• − Z5032 E3 Swivel bracket
• − Z5028 E3/Ci80 Horizontal bracket
• − Z5030 E3 x 2 Angle bracket
• − Z5052 Flying bracket CI6/CI9
• − Z5150 Q Swivel bracket

Part list Z5024 Loudspeaker stand adapter

• − 1 x Z5024 Adapter für Boxenstativ
• − 3 x Fixing bolt M8x16
• − 2 x Hex head screw DIN 933-M8x18-8.8
• − 2 x Spring washer 8.2
• − 2 x Plain washer 8.4

Weight Z5024 Loudspeaker stand adapter

• 0.6 kg/1.3 lb

Assembly

Each adapter is supplied with two M8x18mm hex head screws, spring and plain washers. The adapter is either fitted to the accessories described above or directly fitted to E1 or E3 loudspeakers.

Fixing screws longer than those supplied must not be used. Longer screws can punch in the E1 or E3 threaded inserts and breach the cabinet’s air-tight seal. The adapter may also be fitted using two M8 Safety eyebolts (Q9031).

Alternatively the adapter can be fitted using the two fixing bolts. In this case the spring and plain washers are not used.

Operation

The horizontal angle can be set by slackening the fixing bolt. After horizontal alignment retighten the fixing bolt.

*(1x) D&B Audiotechnik E7925-000 B6-SUB Transport Lid

B6 Sub Transport Lid.

*(1x) D&B Audiotechnik E7473-000 Touring Case 2 x YP

Touring case 2 x YP