RANE RAD16z RAD16z Halogen HAL Interface

RANE RAD16z RAD16z Halogen HAL Interface

The RAD16z is an alternative to standard switch boxes for impractical areas such as in stage floor pockets or above ceilings. Its form factor is a rugged metal box with flexible surface mounting options. The RAD16z is plenum-rated UL 2043. It contains two balanced Mic / Line / Line-Plus inputs and two balanced line outputs on Euroblock connectors.

Features:

• Plenum-rated 2-ch I/O box with logic, single shielded CAT5e or better for up to 500 feet maximum distance
• Alternative to standard switch boxes for impractical areas such as floor pockets or above ceilings
• 2 balanced Mic / Line / Line-Plus inputs and 2 balanced line outputs on Euroblock connectors
• 2 Logic Inputs and Outputs interface other devices to HAL with toggles or commands, such as push-to-talk or mute switches, projectors, lights, alarms, etc.
• Power on/off transient suppression
• 500 V galvanic isolation

Specifications:

• Digital Codec: 24-bit, 48kHz
• Inputs:
  • Microphone (level set in software):
    • Connectors: 1 Euroblock, 6 pins, 3.81 mm pitch, green
    • Impedance: 2.16 kΩ 1%, balanced, 1.08 kΩ + 1.08 kΩ
    • Gain Range (dynamic): +26 to +46 dB Typical, 1 dB steps
    • Gain Range (condenser): +14 to +34 dB Typical, 1 dB steps
    • Maximum Input (dynamic): -16 dBu Minimum, balanced, gain = 26 dB
    • Maximum Input (condenser): -4 dBu Minimum, balanced, gain = 14 dB
    • Equivalent Input Noise: -121 dBu Typical, 20 kHz BW, RS = 150 Ω, 26 dB gain
    • CMRR: -70 dB Typical, RS = 150 Ω, 1 kHz, 26 dB gain
    • Frequency Response 20 Hz – 20 kHz Typical, +0.0/-0.5 dB, at all gain settings
    • THD+N: <0.010% Typical, @ 1 kHz, 20 kHz BW, Rs = 150 Ω, -6 dBFS output, 26 dB gain
    • Phantom Power: +24V 2%, 10 mA maximum
  • Line/ Line+ (balanced):
    • Impedance: 10 kΩ 1%, balanced
    • Gain Range: 0–20 dB Typical
    • Maximum Input (Line Mode): 14 dBu Minimum, < 1% THD
    • Maximum Input (Line+ Mode): 14 dBu Typical, @ 1 kHz, active, left (+) & right (–) signals summed to mono
    • Dynamic Range: 103 dB Typical, 0 dBFS, 20 kHz BW, A-weighted, unity gain
    • CMRR: -50 dB Typical, Rs = 150 Ω, 1 kHz
    • Frequency Response: 20 Hz – 20 kHz Typical, +0.0/-0.5 dB
• Outputs:
  • Connectors: 1 Euroblock, 6 pins, 3.81 mm pitch, orange
  • Impedance: 200 Ω 1%, each leg
  • Maximum Output: 14 dBu Minimum, < 1% THD, 10 kΩ load
  • Dynamic Range: 106 dB Typical, 0 dBFS, 20 kHz BW, A-weighted
  • Frequency Response: 20 Hz – 20 kHz Typical, +0.0/-0.5 dB
  • THD+N: 0.008% Typical, @ 1 kHz, 20 kHz BW, -6 dBFS output, RAD16z input to output
• Indicators:
  • Signal: -50 dBFS Unbalanced/balanced output, green LED, peak-reading
  • Overload: -0.5 dBFS Unbalanced/balanced output, red LED, peak-reading
• RAD Port:
  • Connectors: 1 RJ-45
  • Cable Length: 500 ft. / 152 m Shielded Cat5e cable or better; must be shielded
• Logic:
  • Inputs:
    • Connectors: 1 (shared) Euroblock, 6 pins, 3.81 mm pitch, black, contact closure to ground
    • Internal Pull-Up: 51.1 kΩ, 5.0V Protected to +24V
    • High-Input Level: > 2.0V Minimum, normal state
    • Low-Input Level: < 0.9V Maximum, external circuit must sink > 80 μA to assert
  • Outputs:
    • Connectors: 1 (shared) Euroblock, 6 pins, 3.81 mm pitch, black, relay drive, LED or logic level output
    • Internal Pull-Up: 1.0 kΩ, 5.0V Protected to +30V, reverse-polarity-protected
    • Sink Current: 200 mA Maximum, output FET on
    • LED Drive Current: 2 mA Output FET off, driving an LED with Vf = 2.0V
    • High-Output Level: 4.7V Minimum, output FET off, 0 mA output current
    • Low-Output Level: 0.1V Maximum, output FET on, < 200 mA sink current
• Dimensions: Width x depth x height 4.92” x 3.31” x 1.05” (12.5 x 8.4 x 2.7 cm)
• Weight: 11.9 oz. 337 g